🔥Hayward Turbo TCELL940-Extended life Replacement Salt Cell 40K TCELL-15 GLXW

Description

🔥Hayward Turbo TCELL940-Extended life Replacement Salt Cell 40K TCELL-15 GLXW.
Genuine Factory Hayward TCELL940-W is designed to provide up to 25% more life vs. a Standard T-CELL15. Research the pricing, and you will see this is an exceptional Buy!
FROM HAYWARD WEBSITE:
TCELL940 TCELL940-W
MENU SETTING MAY BE REQUIRED!
The TCELL940 and TCELL940-W are extended life cells designed for pools up to 40,000 gallons. When replacing an existing T-CELL-15, GLX-CELL-15, TCELL940 or TCELL940-W, no re-configuration is necessary.
Configuration of your controller may be required before using the TCELL940 or TCELL940-W chlorinator cell. Refer to the information below. Incorrect configuration will cause inaccurate salt readings, improper operation, and possible system shutdown.
CONFIGURATION is necessary with the following models:
NO CONFIGURATION is necessary with the following models: Connecting to an AQR or AQR900:
Connecting to an AQR-PRO:
Connecting to an AQ-LOGIC-P-4, AQ-LOGIC-PS-x, PL-P-4 or PL-PS-x:
Hayward Pool Products
620 Division Street, Elizabeth NJ 07207 Phone (908)-355-7995 www.hayward.com
• AQR (Aqua Rite - all 2009 or later) - firmware version 1.5 or later
• AQR-PRO (Aqua Rite Pro)
• PL-P-4 (Pro Logic P4)
• PL-PS-x (Pro Logic PS)
• AQ-LOGIC-P-4 (Pro Logic P4)
• AQ-LOGIC-PS-x (Pro Logic PS)
• AQR900 series - all
• AQ-RITE (Aqua Rite - 2008 and earlier) - firmware earlier than version 1.5
• AQ-RITE-XL (Aqua Rite XL)
1. Slide the Main Switch to the “Auto” position.
2. Push the Diagnostic button repeatedly until “t-xx” appears on the display (“t-15” is the factory default). If “t-15” is displayed, skip to
step 4.
3. To change cell type, slide the Main Switch from “Auto” to “Super Chlorinate” and back to “Auto”. Repeat this process until the “t-15” is
displayed.
4. Push the Diagnostic button to exit.
1. Access the Settings Menu by pushing the “Settings” button.
2. Push “>” until Chlor. Config is displayed, then push “+”.
3. Push “>” repeatedly until “Cell Type” is displayed.
4. Push “+” or “-” until “T-CELL-15” is displayed.
5. Exit Settings Menu by pushing the “Info” button.
1. Enter the Configuration Menu.
2. Push “>” until Chlor. Config is displayed, then push “+”.
3. With the Chlorinator Enabled, push “>” repeatedly until “Cell Type” is displayed.
4. Push “+” or “-” until “T-CELL-15” is displayed.
5. Exit Settings Menu by pushing the “Menu” button.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
IMPORTANT INFORMATION
Regarding Extended Pool Filtration cycles, and Low Flow Rate conditions
THE AMOUNT OF CHLORINE PRODUCED BY YOUR SALT CHLORINE GENERATING SYSTEM IS DEPENDENT ON THE LENGTH OF TIME THAT YOUR FILTER PUMP RUNS EVERY DAY. SO, YOUR CHLORINATION SETTING SHOULD BE MATCHED TO THE FILTER PUMP RUN TIME OF YOUR POOL.
Whether you plan to INCREASE or DECREASE the filter pump cycle on your pool, adjust the chlorination setting using the dial on your AquaRite chlorina- tor or the up and down keys on your AquaRite Pro or ProLogic controller. By properly adjusting your setting, you are preventing the over-chlorination or under-chlorination of your pool.
For example, If you plan on doubling the filter pump operating time (say from 8 hours/day to 16 hours/day), then reduce your chlorination setting by a factor of 2 (say from 50% to 25%). If you plan to triple your filter pump operating time, then reduce your chlorination setting by a factor of 3. Likewise, if you reduce your filter pump operating time (say from 12 hours/day to 8 hours/day), then increase your chlorination setting by a factor of 1.5 (i.e. 12/8=1.5)
These adjustments, while necessary and important, are APPROXIMATIONS to the actual adjustment your pool requires. After any chlorination adjust- ment, monitor the pool’s chlorine level closely for 1-2 weeks. If the readings stabilize in the 1-3 ppm range then you are all set—otherwise make another small adjustment (up or down) to increase or decrease the chlorine level. Once the chlorinator is set, it is good practice to check your chlorine levels weekly to ensure operation is normal.
WHEN USING 2 SPEED OR VARIABLE SPEED PUMPS ON LOW SPEED, CHECK TO BE SURE YOUR SALT CELL IS RECEIVING ADEQUATE FLOW. Low flow conditions can result in insufficient water in the cell causing inefficient chlorine production. As a precaution, the cell can be installed vertically or in an inverted manner (see illustration) to keep it flooded with water.
Vertical Installation Inverted Installation
Desired installation configurations when using 2 speed or variable speed pumps.
Hayward is a registered trademark and AquaRite, AquaRite Pro, and ProLogic are trademarks of Hayward Industries, Inc. © 2016 Hayward Industries, Inc.
All other trademarks not owned by Hayward are the property of their respective owners. Hayward is not in any way affiliated with or endorsed by those third parties.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Why spend 9 for the T-CELL15 when you can add 25% more lifespan with this UPGRADED EXTENDED LIFE VERSION
Chlorination for Pools up to 40,000 Gallons.